How to Fix Android App Not Installed Error on Tecno Spark 10 5G Quickly?

App not installed on Android is no more an unknown Error Code during Application installation as many people experience it on a day-to-day basis. An “Application not installed” error message usually pops up when you are trying to download and install an App with a .apk file extension from somewhere other than the Google Play Store. The error is very confusing at first but makes sense when you realize that this unknown Error Code during Application installation is neither a software issue nor a hardware problem. It is a direct outcome of what you do with your device. Yes, you heard that right. Your faulty actions can cause Android App not installed error.

What to do when trying to install the Android APK it says “app not installed”? It is terrible that you can’t install App on your device. But in this article, you will know more about the causes behind this error and the best ways to fix it, read on, here is all you need to know.

Part 1: Common reasons for the “Android App not installed” error

You may ask: Why can’t I download apps on my Tecno Spark 10 5G? Understanding the underlying causes of the “Android App Not Installed” error is crucial for resolving the issue effectively. So, what are the reasons for Android App not installed error? Given below are a few reasons:

1. Insufficient storage

Android software and if data such as photos, videos, music, messages, apps, contacts, emails, etc are stored in the internal memory there is not adequate storage left for another App, leading to Android App not installed error.

2. Corrupted/Contaminated App file

When you do not download Apps from the Play Store and choose another platform to do so, App files are usually corrupted and hence cannot be installed on your device smoothly. You should be doubly sure of the source from where you download an App, check its extension name, and make an effort not to install contained files.

3. SD Card not mounted in the Tecno Spark 10 5G device

At times your phone could be connected to your PC or another electronic device that can access the SD Card from your device. In such situations when you install an App and choose to save it to your SD Card, you will see Android App not installed error because the App cannot find the SD card as it is not mounted in your device.

4. Storage location

You must be aware that certain Apps work their best when stored in the Tecno Spark 10 5G device’s internal memory, whereas others need to be located on an SD Card. If you do not save the App in an appropriate location, you will find that the App isn’t installed because of an unknown Error Code.

5. Corrupt storage

Corrupted storage, especially a corrupted SD Card, is known to cause the Android App isn’t installed error. Even the internal storage can get clogged due to unnecessary and unwanted data, some of which might contain an element that disturbs the storage location. Take this issue seriously as a corrupted SD Card and even clogged up internal memory can put your device in danger.

6. Application Permission

Software operations running in the background and App Permission are not new concepts. Such errors can also cause the Unknown Error Code during App installation.

7. Incorrect file

If you already have an App installed but download another variant of it having a distinct signed or unsigned certificate can also make the Android App not installed error pop-up. This sounds technical, but this and all the other reasons listed above can be tackled by you.

The Unknown Error Code during Application installation can occur due to any one or more of the reasons stated above. So read them carefully and understand them well to avoid such glitches in the future.

Part 2: One-click to fix App not installed on Android error

So App not installed on your Tecno Spark 10 5G or tablet? The most horrible part is that this issue may come out of the corruption in the system files. In this situation, Android apps won’t be installed no matter what measures you take. Android system repair is the only effective solution to deal with this issue.

Android system repair used to require high technical skills. But most of the users know little about technical things. Well, worry not! Dr.Fone - System Repair (Android) allows you to repair Android easily, that is, complete the fix with just one click.

Dr.Fone - System Repair (Android)

A powerful tool to fix the “Android App not installed” error in one click

Fix all Android system issues like Android App not being installed, the system UI not working, etc.
One-click to fix Android App not installed. No technical skills are required.
Support all the new Tecno Spark 10 5G devices, etc.
On-screen instructions are provided to prevent any misoperation.

3981454 people have downloaded it

Note: Getting your Android system repaired may erase the existing device data. It is recommended that you should back up your Android data before starting the Android repair.

The following steps illustrate how to fix the “Android App not installed” error in one click:

Install Dr.Fone on your Windows. After that, launch it, and click “System Repair”. Connect your Android to the computer.

Select the “Android” option and click “Start”.

Select device information, such as brand, name, model, country, etc., from each field, and type “Next”.

Follow the on-screen instructions to boot your Android in download mode, and allow the tool to download the firmware to your device.

After the firmware is downloaded, the tool will start to repair your Android, hereby fixing the “Android App not installed” error.

safe & secure

Part 3: How to fix App not installed error on Android

We understand that it can be a tricky situation to be in when Android App not installed error pops up, but what if we tell you can get rid of it in easy and simple steps? Yes, there is!

#1. Delete unnecessary files/Apps

Insufficient storage can prevent the app from being installed. Make some storage space on your device by cleaning unwanted data and deleting extra media and other files. You can also get rid of heavy Apps by:

Visiting “Settings” on your device. Then select “Manage apps”, “Application Manager” or “Apps” (varies based on device model or version) from the list of options before you.

Now select the App you wish to uninstall and wait for the App Info screen to open, then click on “Uninstall” as shown in the screenshot.

You can also uninstall the unnecessary application on the home screen, just long-press the app you want to uninstall until you see the “uninstall” icon. Click “Uninstall”, then, you need to click “OK” to confirm the uninstall process.

#2. Use only Google Play Store

As you are all aware, the Play Store is specially designed for Android software and contains only trusted and safe Apps. It is often known as the “Android Market” because it is loaded with different types of Apps to stiffly all your needs so that you don’t have to rely on other third-party sources to purchase/install Apps.

#3. Mount your SD Card

Another remedy for Android App not installed error is to make sure that the SD card inserted in your device is not inaccessible.

To check the same:

First, disconnect your Tecno Spark 10 5G from your PC and then visit “Settings” on your Android and select “Storage” from the options that appear. Finally, click on “Mount SD Card” at the Storage Info screen.

You can now restart your device and try to install the app now, it should work!

#4. Choose App location wisely

It is advisable to not tamper with the App’s location and let the software decide where it needs to be placed. As far as possible, let the Apps be in your device’s internal memory.

#5. Format SD Card

The chances of your SD Card being corrupted are very high. You can format it either while it is in your device or externally.

Now to Clean up your SD Card, simply visit “Settings” and select “Storage” and tap on “Format SD Card” and mount it once again to use it smoothly.

#6. App Permissions

You can reset App permissions to combat the Android App not installed error by Visiting “Settings” and then selecting “Apps”. Now access the Apps menu and hit “Reset App Preferences” or “Reset application permissions”. This will allow third-party apps to get installed on your device.

#7. Choose the correct App file

Make sure to always download an App file only from a trusted and safe source to avoid any errors during installation.

#8. Reboot your device

Finally, if nothing else works, restart your device to end all operations which could be causing the said error. To reboot, just press the power button till you see a pop-up. Select “Restart” and wait for your device to reboot.

Conclusion

Encountering the “App Not Installed” error on Android can be frustrating, but by understanding the causes and implementing the appropriate solutions, you can overcome this issue. We saw that Android App not installed error can be fixed quickly if you keep in mind the tips given in this article. However, please ensure that you follow each instruction carefully to avoid any further goof up.

safe & secure

Tecno Spark 10 5G Bootloop Problem, How to Fix it Without Data Loss

Have you, like many other users, faced the bootloop Android problem and wondered what exactly is Android boot loop. Well, Android boot loop is nothing but an error that makes your phone switch on itself every time you manually turn it off. To be precise, when your Tecno Spark 10 5G does not remain switched off or powered off and starts to boot up automatically after a few seconds, it might be stuck in the boot loop Android.

An Android boot loop is a very common problem and is one of the first symptoms of a soft-bricked device. Also, when your device is experiencing Android boot loop issue, it does not start normally to reach the Home or Locked Screen and remains frozen at the Tecno Spark 10 5G device’s logo, Recovery Mode or a lit-up screen. Many people fear losing their data and other files due to this error and thus, it is a very confusing situation to be in.

We understand the inconvenience caused, therefore, here are ways to tell you how to fix the bootloop problem in Android devices without losing any important data.

However, before moving on, let us learn a little about the causes for the Android boot loop error.

Part 1: What might cause the bootloop issue on Android?

Android boot loop error might seem weird and unexplainable but it occurs because of some specific reasons.

Firstly, please understand that it is a misnomer that boot loop error occurs only in a rooted device. Boot loop Android error can also occur in a stock device with the original software, ROM, and firmware.

In a rooted device, changes made, such as flashing a new ROM or customized firmware which are not compatible with the Tecno Spark 10 5G device’s hardware or existing software, can be blamed for the boot loop problem.

Moving on, when your device’s software is unable to communicate with the system files during the start-up process, Android boot loop problem may arise. Such a glitch is caused if you have recently updated the Android version.

Also, corrupt App update files may also cause the bootloop Android issue. Apps and programs downloaded from unknown sources bring in a particular type of virus that prevents you from using your device smoothly.

All-in-all, Android boot loop error is a direct outcome of when you try to tamper with your device’s internal settings.

Hence, if you are looking for ways to guide you about how to fix boot loop issue, you will have to revamp the Tecno Spark 10 5G device internally by either resetting it or adopting a recovery method.

Read on to know more about how to fix the bootloop error without any data loss when your device suffers from the bootloop Android problem.

Part 2: One click to Fix Android Bootloop without factory reset

If you are trying to figure out how to fix boot loop, the first option you have is the one-click fix to Android Bootloop which involves using the Dr.Fone - System Repair software.

This is designed to repair any data corruption on your device and restores your firmware to its usual working condition.

Dr.Fone - System Repair (Android)

One click to fix boot loop of Android

#1 Android repair solution from your PC, can fix a wide range of Android system issues, such as boot loop, black screen, etc.
The software requires no technical expertise, and anybody can use it
A one-click solution when learning how to fix Android boot loop
Not require root Android phones.
Works with most Tecno Spark 10 5G devices, including the latest Tecno Spark 10 5G phones like S22
Simple and easy-to-use user interface

4,689,059 people have downloaded it

To help you get started, here’s a step-by-step guide on how to use Dr.Fone - System Repair.

Note: This method can erase data on your device, including your personal files, so make sure you’ve backed up your device before proceeding.

Step #1 Download the Dr.Fone - System Repair software from the website and install it onto your computer.

Open the software and select the System Repair option from the main menu to fix the Android bootloop error.

Step #2 Connect your Tecno Spark 10 5G to your computer using the official cable and select the “Android” option from the three menu items. Click “Start” to confirm.

You’ll then need to input the Tecno Spark 10 5G device information, such as your carrier info, device name, model, and country/region in order to ensure you’re downloading and repairing the correct firmware to your phone.

Step #3 Now you’ll need to put your phone into Download Mode to remove the Android bootloop.

For this, you can simply follow the onscreen instructions for both phones with and without home buttons.

Click “Next”, and the software will begin downloading the firmware repair files.

Step #4 Now you can sit back and watch the magic happen!

Make sure your computer stays connected to the internet, and your device stays connected to your computer throughout the entire process. Once the firmware has been downloaded, it will be automatically installed onto your mobile device, removing the boot loop Android error.

You’ll be notified when the process is done and when you can remove your device and start using free from the boot loop Android error!

safe & secure

Part 3: Soft reset to fix Android bootloop issue

When your device is stuck in Android boot loop, it does not necessarily mean that it is bricked. Boot loop might be occurring due to a simpler problem which can be fixed by turning off your device. This sounds like a home remedy for a serious problem but it works and resolves the problem most of the time.

Follow the steps given below to soft reset your device:

Turn the Tecno Spark 10 5G device off and take out its battery.

If you cannot take the battery out, let the phone be off for about 3 to 5 minutes, and then turn it back on.

Simply performing a soft reset on your device can help you if you are looking for solutions for how to fix the bootloop issue. This a very useful method as it does not result in any kind of loss in data and protects all your media files, documents, settings, etc.

In case the Tecno Spark 10 5G device does not turn on normally and is still stuck in the bootloop Android problem, be prepared to use the troubleshooting techniques given and explained below.

Part 4: Boot into Safe Mode to fix Android boot loop

Booting your Tecno Spark 10 5G into Safe Mode is a useful troubleshooting step to fix boot loop issues caused by third-party apps. When in Safe Mode, the Tecno Spark 10 5G device will start up with only essential system apps, and any downloaded apps that might be causing conflicts won’t run. Here’s how you can boot your Tecno Spark 10 5G into Safe Mode to address the boot loop problem:

Step 1: Power Off Your Device

Hold down the power button until it turns off completely.

Step 2: Access Safe Mode

To enter Safe Mode, follow these steps based on your device model:

For most Android devices: Press and hold the power button to turn on your device. As soon as the manufacturer’s logo appears, press and hold the Volume Down button until the Tecno Spark 10 5G device finishes booting. You should see “Safe Mode” displayed in the bottom left or right corner of the screen.
Some devices might require slightly different key combinations. Refer to your device’s user manual or perform an online search for the specific method to enter Safe Mode for your model.

Step 3: Observe the Tecno Spark 10 5G device

Once your device has booted into Safe Mode, use it for a while to see if the boot loop issue persists. If the boot loop doesn’t occur in Safe Mode, it indicates that the problem is likely caused by a third-party app.

Step 4: Identify and Uninstall Problematic Apps

Now that you’re in Safe Mode, it’s time to identify the troublesome app. Start by uninstalling recently installed apps one by one until the boot loop problem is resolved. After each uninstallation, restart your device normally to check if the boot loop still occurs. Continue this process until you find the problematic app.

Step 5: Restart Normally

Once you’ve identified and uninstalled the problematic app, restart your device normally to exit Safe Mode. Your Android device should now start up without getting stuck in a boot loop.

By following these steps and using Safe Mode to isolate problematic apps, you can effectively troubleshoot and resolve boot loop issues on your Tecno Spark 10 5G.

Part 4: Factory reset to fix Android bootloop issue

Factory reset, also known as Hard Reset, is a one-stop solution for all your software resulting in issues. Android boot loop being such problem, can be easily overcome by performing a factory reset.

Please note that all your device’s data and settings will be deleted by adopting this method. However, if you have a Google account signed in on your Tecno Spark 10 5G, you will be able to retrieve most of your data once the Tecno Spark 10 5G device turns on.

To factory reset your Android boot loop device, you must first boot into the Recovery Mode screen.

To do this:

Press the volume down button and power button together until you see a screen with multiple options before you.

When you are at the Recovery Mode screen, scroll down using the volume down key, and from the options given, select “Factory Reset” using the power key.

Wait for your device to perform the task and then:

Reboot the phone in Recovery Mode by selecting the first option.

This solution is known to fix the boot loop error 9 out of 10 times, but if you still can’t start your Tecno Spark 10 5G normally, consider using a CWM Recovery to resolve the Android boot loop issue.

Part 5: Use CWM Recovery to fix bootloop on rooted Android

CWM stands for ClockworkMod and it is a very popular custom recovery system. To use this system to solve the boot loop Android error, your Tecno Spark 10 5G must be rooted with CWM Recovery System which basically means CWM must be downloaded and installed on your device.

Furthermore, to use CWM Recovery to fix boot loop on rooted Android devices, follow the steps given below:

Press the home, power, and volume up buttons to launch the CWM Recovery screen.

Note: you might have to use a different combination of keys to enter into Recovery Mode, depending on your device’s model.

Scroll down using” the volume key to select “Advanced”.

Now select “Wipe” and choose to wipe “Dalvik Cache”.

In this step, select “Mounts and Storage” to click on “Wipe” or “Cache”.

Once this is done, make sure to reboot your Tecno Spark 10 5G.

This process with successfully fix the Android boot loop error and not cause any loss of data stored on your device stuck in boot loop.

So the bottom line is that boot loop Android issue may seem like an irreparable error but it can be resolved by carefully following the techniques explained above. These methods not only tell you how to fix the bootloop problem but also prevent it from occurring in the future.

An Android boot loop is a common phenomenon with all Android devices because we tend to tamper with our device’s internal settings. Once the ROM, firmware, kernel, etc are damaged or rendered incompatible with the Tecno Spark 10 5G device’s software, you cannot expect it to function smoothly, hence, the boot loop error occurs. Since you are not the only one suffering from the Android boot loop problem, be rest assured that the ways, given above, to combat it are recommended by users facing similar troubles. So, don’t hesitate and go ahead to try them on.

safe & secure

Tecno Spark 10 5G Not Connecting to Wi-Fi? 12 Quick Ways to Fix

Nowadays, it’s pretty much essential to have your Tecno Spark 10 5G or smartphone connected to the internet. Whether you’re watching videos, looking something up, or using any kind of app, you need the internet for these applications to function correctly.

This is why it can so annoying when it gets to a point where the internet connection isn’t working. However, the problem of a web page not loading correctly is just the tip of the iceberg.

There are plenty of problems you could experience, whether it’s the Wi-Fi network keeps disconnecting on its own without any warning, perhaps a security issue where the passcode or IP address isn’t being registered properly, or even if the connection is just being super slow, even if there’s no reason too.

Luckily, despite there being so many problems out there, there are also many solutions. Today, we’re going to share with you the complete definitive guide to help you get your Tecno Spark 10 5G connected and free from problems and issues.

Part 1: Restart your Tecno Spark 10 5G

Begin by powering off your Tecno Spark 10 5G and unplugging your router. Wait for about a minute before plugging in the router and turning on your device. This simple reset can often restore stable connections and fix Android wifi not working.

Part 2: Turn on Airplane mode and turn off

Turn on Airplane Mode for a few seconds, then turn it off. This maneuver refreshes your device’s network connections and might rectify the Android not connecting to wifi issue.

Part 3. Check Wi-Fi Router settings

The third step you’ll want to take is making sure the internet router in your house is working properly and is actually sending internet data to your Tecno Spark 10 5G. Of course, if you have other internet-enabled devices connected to the same router and they’re working fine, you know this isn’t the problem.

However, if you’ve got a problem with Wi-Fi not working on your Android and other devices in your home or office, you know you’ve got a router problem. Here’s how to solve it.

Go to your internet router and check the indicator lights
While this depends on your device, a green or blue light will mean the connection is good, whereas a red light indicates a problem
Press the Restart button on your router and wait ten minutes before reconnecting your device and connecting again
Call up your internet provider to see if there’s an internet connection issue in your area
Open your web browser and log into your router settings to ensure your Tecno Spark 10 5G is connected to the Wi-Fi network and is allowed to send and receive data

Part 4. Boot your Android in safe mode

If you’re unable to connect to the internet, but other devices have no issues, you may find the issues is coming from within your Tecno Spark 10 5G itself. Fortunately, there are ways you can see whether this is the problem.

The best way to do this is to boot your device in Safe Mode. The process for doing this will depend on the make and model of your Tecno Spark 10 5G, but the basic process goes as follows;

Turn off your Tecno Spark 10 5G by holding down the Power button and tapping Power Off. Wait a few minutes to ensure the Tecno Spark 10 5G device is completely off
Press and hold the Power button to turn your phone on, but the press and hold both the volume up and volume down buttons at the same time
You will see the words ‘Safe Mode’ appear on your screen as the Tecno Spark 10 5G device loads
Now you will be booted in Safe Mode. Try connecting to the internet again to see if it works

If your device connects to the internet while in Safe Mode, you’ll know you have a problem with an app or service that’s running on your device. If this is the case, you’ll need to go through your apps and delete them and then reinstall them one at a time until you find the app or service that is causing your internet problems.

Part 5. Check the Android Wi-Fi adapter

If you’re using a Wi-Fi adapter on your device to connect to the internet, you’ll need to make sure this is working. This could be an adapter on your Tecno Spark 10 5G itself, especially if you’re using an older device, or if you’re using an adapter to boost the ranger of your router network.

You need to check both of these to make sure your connection is working properly.

If using an Android Wi-Fi adapter, make sure all the Tecno Spark 10 5G device drivers are up to date, and if you’re using an app, make sure the app is updated, and all the settings allow an internet connection
If you’re using a router adapter, make sure it’s set up properly, and your Tecno Spark 10 5G is connected to the adapter using the correct passwords. Try connecting another device to see if the internet connection is working on there
Whichever method you’re using, try disconnecting your Tecno Spark 10 5G and forgetting the network, and then reconnecting and entering the right password to refresh the connection

Part 6. Check SSID and IP address on Android

To make a Wi-Fi connection work, your Tecno Spark 10 5G needs to match two codes that connect and relate to your router to establish the connection and work correctly. These are known as the SSID and the IP address.

Every wireless device will have its own codes and making sure they’re matched to the network you’re connecting to is crucial to ensuring the internet is working on your Tecno Spark 10 5G. Here’s how to check on your Tecno Spark 10 5G to make sure everything is correct.

Tap the Settings menu option, followed by Wi-Fi on your Tecno Spark 10 5G
Turn on your Wi-Fi network and connect it to your router
Find the router name (SSID) and make sure it’s exactly the same as the SSID written on your router
Once connected, tap the Wi-Fi network and you will see the IP address. Check both your phone and the router codes to make sure this number matches

When these numbers are matching, if your Android is still not connecting to wifi, you’ll know this wasn’t the problem.

Part 7. Fix Android system issues in one click

If none of the solutions above are working, this could indicate a real problem with the firmware and operating system of your Tecno Spark 10 5G. Fortunately, a fast solution to get everything working again is to completely repair the software of your phone.

You can do this easily using powerful Android recovery software known as Dr.Fone - System Repair (Android) . This is the leading repair tool on the market and is designed to fix and repair any firmware and software problems you may be having.

Dr.Fone - System Repair (Android)

A one-click tool to fix Wi-Fi not working on Android

Can repair Android from any problem including the black screen of death
A trusted software application used by 50+ million people around the world
The most user-friendly mobile repair application available right now
Supports over 1,000+ Android models and devices
A world-class customer support team to help you whenever you need them

3,483,527 people have downloaded it

To help you have the best and the most accurate experience when using the Dr.Fone - System Repair (Android) application, here’s a complete step-by-step guide on how to use it.

Step One Make your way over to the Wondershare website and download the Dr.Fone - System Repair (Android) software. Install it onto your computer by following the on-screen instructions.

Once installed, connect your Tecno Spark 10 5G to your computer using a USB cable, and open the software, click “System Repair”.

Step Two Click the “Android” option in the menu and then click “Start” to begin the Repair process.

Step Three On the next screen, go through the options and use the drop-down menus to make sure the information is correct for your individual device. Accept the terms and conditions of the software, and then click the “Next” button.

Step Four Confirm you want the software to carry out the repair process by typing the ‘000000’ code into the pop-up box and pressing Confirm. Make sure you read everything displayed in this box beforehand to know what’s happening.

Step Five Now put your phone into Download Mode by following the on-screen instructions, so your device is ready for the repair process. The method for getting your phone into Download Mode will vary depending on your device, so make sure you’re following the right instructions.

Step Six Once the software has detected your device in Download Mode, it will automatically begin the repair process. You need to make sure your device stays connected throughout this time, and your computer stays on.

The whole process is automatic, so you won’t need to do anything until it’s finished. Once completed, you can disconnect your phone and start connecting it to the internet as normal!

safe & secure

Part 8. Check the Wi-Fi connectivity on another phone

When experiencing problems with your Wi-Fi network, it’s worth noting the problem might not be with your phone, but rather the Wi-Fi network itself. This is why it’s important to make sure you check the connection on another device.

Of course, if you’re already using another phone on your Wi-Fi network, you know this isn’t the case. However, if you’re not sure, here’s what you need to do;

Get another Android or iOS phone or tablet
Open the Settings menu and connect to the Wi-Fi network you’re having problems with
Enter the password and connect to the network
Open a web browser on the phone and try loading a web page
If the page loads, you know the Wi-Fi network isn’t the problem
If the page doesn’t load, you know you’ve got a problem with your Wi-Fi network

Part 9. Change the password of the Wi-Fi

Each Wi-Fi network router will give the opportunity to choose and change the password you have to let devices connect to your network. It’s important you try changing this because you never know if someone else has accessed your network and could be blocking your device. Here’s how it works;

Log onto your computer and open your Wi-Fi settings
Depending on the brand and method of your individual router, navigate to the Wi-Fi password settings menu
Change the password to something complicated using all available digits and characters
Save the password and restart the router to disconnect all devices
Now connect your Tecno Spark 10 5G to the router using the new password

Part 10. Reset network settings on Android

Just like the method above where you’ll be effectively resetting the network settings on your router, if this hasn’t worked, you’ll be able to reset the network settings on your Tecno Spark 10 5G, hopefully removing the bugs and allowing you to connect.

Here’s how you can do this easily on your Tecno Spark 10 5G;

From the home screen of your Tecno Spark 10 5G, open the Settings menu
Tap the Backup & Reset option
Tap the Reset Network Settings option
Tap the Reset Network option
If you need to, enter the PIN number or passcode for the Android device, and the Tecno Spark 10 5G device will confirm the reset has taken place
Reconnect your Tecno Spark 10 5G to your Wi-Fi network for the changes to take effect

Part 11. Clear partition cache in recovery mode

As you continue to use your Tecno Spark 10 5G, the partition cache will fill up with data your device needs and doesn’t need. However, by clearing your device’s partition cache, you can make clear up some space which should help your device have enough memory to connect to the internet.

Turn off your Tecno Spark 10 5G
Turn it on by holding down the power button, volume button, and home button
When your phone vibrates, let go of the Power button, but continue to hold the volume button
When a menu is displayed, use the volume buttons to navigate the menu
Select the Android System Recovery option, followed by Wipe Cache Partition
Restart your device and connect to the internet

Part 12. Reset factory settings

If worse comes to worst, another option you have is to factory reset your Tecno Spark 10 5G. As we’ve spoken about above, while using your phone from the day you started using it, your device will fill up with files and data which can become messy and causes bugs.

However, by factory resetting your device, you can start again from the factory default from which you first received it, ultimately clearing the bugs. Make sure you back up your device before proceeding because it will erase your personal files.

Open the Settings menu on your Tecno Spark 10 5G
Navigate to System > Advanced > Reset Options
Tap the Reset phone option, and enter your PIN code if required
Tap Erase Everything
Wait for your phone to complete the process
Restart your device and connect to the internet

safe & secure

Change Location

How to Fix Android App Not Installed Error on Tecno Spark 10 5G Quickly? | Dr.fone